---

@maik wrote:

But what happens to my Swisscom DynDns that ends at xxx.internet-box.ch?

Can I simply re-enter this in the gateway?

---

With the FritzBox 5490 some time ago I was able to easily get it working again…

@Herby

Thanks for your answer.

I’m currently more concerned with the topic of IGMP. You read about so many problems that Ubiquiti products put me off a bit.

[Edit]

Where do you get the information for Swisscom’s DynDNS so that you can enter it on a third-party router? or is this really only possible with the Swisscom internet boxes?

Greetings mAik

Hello everyone, I just bought the switch and the USG 3P and put them into operation, so far everything is working. I also copied the JSON file from BurningRolli exactly as it is, saved it in the editor and stored it in the folders. The USG restarted, the rules were all stored, but the box has absolutely no connection to the Internet, what could be the reason? I’m more of an amateur when it comes to networking, so it’s possible I made a mistake somewhere. However, I implemented the rules exactly as shown in the pictures in the instructions. I would be happy for help and tips. LG Nik

Hi @Stegeckiett44,

The picture stops because the TV box switches from unicast to multicast but cannot find the stream. This is typically the case after 5 - 10 seconds. Your problem can be found in the IGMP server or the FW rules. It may be that the config is not clean. Force provisioning again.

The FW rules allow these unicast or multicast connections, but not just from anywhere, but as a source limited to the Swisscom servers.

If that doesn’t work, send me the config via PM.

Greetings

Roli

Hi @Donkioto,

If I understand you correctly, you had a connection before copying config.gateway.json, but not afterwards.

Delete the file and provision the USG again. That should get the USG up and running again.

This happens when the json file is not valid and the USG gets stuck.

See earlier in this thread how the file is formatted and validated.

Otherwise report again.

Greetings

Roli

Hi @maik,

---

I’m currently more concerned with the topic of IGMP. You read about so many problems that Ubiquiti products put me off a bit.

Once the IGMP server is running, it is running. I just took a look, I made the first post on this topic on May 3, 2017. Since then I have never had any problems with the IGMP, nor with testing firmware etc.

But it’s true, Ubiquiti has one or two shortcomings. These construction sites have increased with the introduction of the UniFi® Dream Machine or UniFi® Dream Machine Pro. These are the latest generation gateways, but the functions are implemented very superficially. This is missing, for example. the IGMP server.

I would say: Such a real banana product! (it matures with the customer).

The alternative to the IGMP server exists and has been running for me for a few days:

You bypass the USG and also feed the IB network into a VLAN only network behind the USG, which is only connected to the TV boxes. If necessary, you can create static routes in the IB in order to make the internal networks of the USG known to the IB.

Advantage: No adjustments with the config.gateway.json and thus problems with the IGMP server.

Disadvantage: TV box apps such as: Plex no longer has access to internal resources so easily (Firewall Rules USG).

Best regards

Roli

P.S. Many thanks to @Jeickeukei13 for the tip, he solved his problem the alternative way.

Yes, where did he do that? The communication is so one-sided 2021).

Some time ago I wrote in another thread:

Although you can put a Swisscom TV-Box behind a USG with special know-how, you should avoid this whenever possible.

The new approach from @BurningRoli (who now certainly has a lot of USG special know-how) to bypass the USG for the Anschluss of the TV-Box via VLAN corresponds exactly to this strategy.

The following probably applies to every USG user: The simplest solution is to either connect the Swisscom TV-Box directly to the Internet box or, if this is not possible using a LAN cable, to virtually “loop” the connection through the USG via a VLAN construct.

Werner

@BurningRoli Sali Roli, no the USG is up again, the SC internet box no longer has a connection to the internet. neither live image nor replay, so it doesn’t start up at all because it can’t seem to establish a connection. I have a switch behind it and the SC connected directly to a port. I didn’t change anything about the port profiles, I just created a few networks, but they shouldn’t have any influence. What I’m not sure about is whether I put your JSON file in the right place? I have attached the PrtScreens for you. I read somewhere else that the IP 224.0.0.0 has to be in the firewall somewhere? Did I do something wrong?

---

@BurningRoli wrote:

I would say: Such a real banana product! (it matures with the customer).

---

If only it would at least mature… the firmware updates come with enormous frequency, but they don’t fix a lot of things that have been wrong for a long time.

I took part in requests x years ago in which hundreds of users in the official UniFi forums demanded, for example, that the dysfunctionally implemented WLAN time control be corrected. An absolute basic feature that every 40 franc router has had for 10 years. The “powerful” UniFi system still doesn’t work, even though the employees in the forums promised years ago that they wanted to correct it.

I mean, I’m not fundamentally against UniFi… for setting up a WiFi network over a slightly larger area or several levels, it’s just a very comfortable and affordable solution that I use regularly. But at the end of the day, you still have to realistically say that this company, with its constantly new (and renewed) products and constantly new software versions, obviously places too much emphasis on bringing new things onto the market and not enough on making the existing functions reliable and to function stably. (So ​​actually similar to QNAP, although much less bad ;-))

---

@maik wrote:

Hi @BurningRoli

Thank you for your detailed answer.

That would be a possibility, since I have FTTH I actually wanted to eliminate the Internet box. But another problem is Swisscom’s DynDns. There is no data to get it running without an Internet box. I think Swisscom simply doesn’t want that either. I actually don’t think it’s a good thing, since the subscription fee stays the same and it’s up to me which device I want to use.

---

Try with:

Host name: xxx.internet-box.ch

Username and password from the Swisscom login.

At least that’s how the service works for me on a Fritz!Box 5490

@Herby

Thanks for the tip. I don’t own USG/UDM yet. I wanted to find out more about it first.

I’m actually very interested in these Ubiquiti products. However, apart from the lousy WiFi coverage of the IB Plus, everything works fine. I know the USG doesn’t have WiFi, so I would do this with 2 APs from Unifi.

I also like to tinker around a bit, but I don’t want to upset my family members if they suddenly no longer have access to the TV boxes or the Syno externally. The USG / UDM would therefore have to cover these basic functions. It doesn’t help me if I can administer my network well and set it up according to my wishes and then the “normal” everyday things no longer work.

Greetings mAik

@cslu… there are also bananas that rot on the tree.

I completely agree with you, marketing before sustainability. There is still a lot of potential in SW development. UBNT maintains too many HW platforms.

I now have an access point, the IW-AC-PRO, which now has LTS status. This means I have to replace it within a year, after which it will no longer be supported. Greetings from planned obsolescence!

---

@maik wrote:

…

I also like to tinker around a bit, but I don’t want to upset my family members if they suddenly no longer have access to the TV boxes or the external Syno. The USG / UDM would therefore have to cover these basic functions. It doesn’t help me if I can administer my network well and set it up according to my wishes and then the “normal” everyday things no longer work.

---

Trust me, messing around won’t get any better. The saying: “Daddy, did you do something on the Internet again” is well known, and the answer is also: “It’ll be right back.” There is always an issue to be fixed in the UBNT environment, see previous post by @cslu.

@BurningRoli Do you have practical and good instructions for using the VLAN solution? So we could get the box back into operation quickly and easily? Otherwise there is almost no way to solve the entire network in a simple way so that it doesn’t go via the USG…

@BurningRoli

That’s exactly what intimidates me, but I’m also excited by the challenge. I’m not in a hurry. I will monitor the topic carefully and decide whether the product is right for me.

---

@Donkioto wrote:

@BurningRoli Do you have practical and good instructions for using the VLAN solution? So we could get the box back into operation quickly and easily? Otherwise there is almost no way to solve the entire network in a simple way so that it doesn’t go via the USG…

---

I just wanted to write to you that it is important that the base works, so my suggestion: get the original setup with the Swisscom components up and running. Contact Kundencenter, they will help you. If so, PM me. It’s not magic. It ran after 10 minutes and cursing twice 😉 I’ll describe it when I get the chance.

Greetings Roli

@BurningRoli So that’s theoretically working, but we have a network cable that goes down to the TV room. That’s why we switched to Unifi, because theoretically the stuff works. (AC-AP and switch etc.) but we have the problem that Swisscom comes in with internet where we can’t do anything. as if the internet box comes up and over the network cable we go down to the switch where the TV box is. Unfortunately it is not possible to pull two cables down… The structure here sounds more complicated than it is 😄

I recommend not using USG either way.

I think the unifi UAP’s are cheap and good and can do quite a lot in terms of functionality. But they are also designed more for the business sector. But because they are so well-known and simple, consumers also like to use them. But then you are surprised that the WPS or the time control does not work or exist in the way you are used to with home devices.

The USW’s are also fine if you want to configure them comfortably.

But I don’t see the USG in a professional environment. There are too many queues in many areas. These are also rather unsuitable for home use because certain functions still have to be muddled in via json.

This may be because home users like the supposed graphics via the unifi controller. However, the UAP’s are not good devices in terms of either software or hardware. My opinion.

Fortunately, the UAPs can also be easily integrated independently of the USG.