Informationen zu c.jaquier

c.jaquier · ‎13.01.2021

My line has been activated on January 11th and I can confirm it is running G.Fast. My modem (Draytek Vigor166) synchonizes at around 450/95 Mbps (much more than the 225/60 announced by the checker).

c.jaquier · ‎10.12.2020

Let me rephrase: Has anyone a DSL speed of 225/60 Mbit/s or higher without being on G.Fast? Thank you

c.jaquier · ‎10.12.2020

Thanks for the summary, greatly appreciated. I got it now 👍

c.jaquier · ‎10.12.2020

Peut-être qu'en reformulant ma question... Est-ce que quelqu'un a un débit supérieur ou égal à 225/60 Mbit/s sans avoir sa ligne en G.Fast ? Merci

c.jaquier · ‎10.12.2020

I looked at my HE tunnel settings and the maximum MTU that can be set for the tunnel is 1480. This is the default value and the one my tunnel is using. I changed back the MTU to default on my IPv6 interface on my pfsense router and it seems that nowhere a PMTU of 1480 is advertised. > tracepath -6 www.swisscom.com 1?: [LOCALHOST] 0.044ms pmtu 1500 1: pfsense.localdomain 3.611ms 1: pfsense.localdomain 1.552ms 2: tunnelxxxxxx.tunnel.tserv23.zrh1.ipv6.he.net 44.482ms 3: e0-16.core2.zrh3.he.net 44.857ms 4: equinix-zrh-v6.ip-plus.net 65.396ms 5: zhh-015-lo0-0.ip6.ip-plus.net 40.757ms 6: 2001:918:ce::45 42.078ms 7: 2a02:a90:4024:fff:8000::15 44.938ms asymm 8 8: no reply I then changed the MTU of my IPv6 interface on the pfsense router to 1480 and can successfully connect to swisscom.ch or cff.ch. > tracepath -6 www.swisscom.com 1?: [LOCALHOST] 0.036ms pmtu 1500 1: pfsense.localdomain 3.762ms 1: pfsense.localdomain 2.410ms 2: pfsense.localdomain 1.874ms pmtu 1480 2: tunnelxxxxxx.tunnel.tserv23.zrh1.ipv6.he.net 41.883ms 3: e0-16.core2.zrh3.he.net 45.583ms 4: as3303.swissix.ch 42.456ms 5: zhh-015-lo0-0.ip6.ip-plus.net 41.472ms 6: 2001:918:ce::47 45.712ms 7: 2a02:a90:4024:fff::15 36.467ms 8: no reply As you can see, my router advertises a PMTU of 1480. I wonder what happened when my IPv6 interface was set to an MTU of 1500. Packets larger than 1480 should not have made it through the tunnel and I guess the tunnel interface should have replied back with a ICMP packet so that my host sends smaller packets. But then the same should have happened with swisscom.com and I shouldn't have had any issues!? I probably have to read all your replies again 😉

c.jaquier · ‎09.12.2020

Hi all, Sorry for cross-posting here but I didn't get any relevant answer to my questions in the French forum. I hope I'll have a better luck here. After more than 7 years using CATV, I'm switching to DSL to have a faster upload. The checker announces 225/60 Mbps for my location. I'm going to use a bridge modem and I wanted to buy a G.Fast model because it seemed to me that with VDSL2 the profiles were only up to 200 Mbps. Therefore I concluded that my line would be using G.Fast. Other addresses in my neighborhood have speeds up to 400/100. My line will be activated on January 11th but I already received my hardware (Wingo) but no G.Fast SFP. I contacted the support and they told me that my line doesn't support G.Fast!? I'm a bit surprised. Is this really the case? Is it possible to get 225/60 (or even 400/100 elsewhere in the neighborhood) without G.Fast?

c.jaquier · ‎09.12.2020

Euh... je ne suis pas encore en DSL, je suis actuellement sur le câble. Ma ligne doit être activée le 11 janvier 2021. Merci quand même pour votre réponse.

c.jaquier · ‎08.12.2020

I'm on CATV (soon to move to Wingo DSL) and I'm using an IPv6 tunnel from HE.net. I was not able to connect to swisscom.ch or sbb.ch. That's the main 2 websites that failed for me on IPv6, most others works fine. Reading this thread, I just lowered my MTU to 1472 on my tunnel interface in pfsense and I can confirm that I can now successfully access both website via IPv6 🙂

c.jaquier · ‎08.12.2020

Bonjour, Après plus de 7 ans en CATV, je passe en DSL afin d'avoir un upload un peu plus véloce. Le checker m'annonce 225/60 Mbit/s à mon adresse. Je vais utiliser un modem en bridge et du coup, je voulais prendre un modèle G.Fast car il me semblait qu'en VDSL2 les profils ne montaient qu'à max 200 Mbit/s. Du coup, j'en ai conclu que ma ligne serait en G.Fast. En essayant dans le checker d'autres adresses de mon quartier, je vois que le meilleur monte à 400/100. J'ai reçu mon matériel (Wingo) et pas de SFP G.Fast. Je contacte le support et on me dit que ma ligne ne supporte pas le G.Fast !? Est-ce vraiment le cas ? Possible d'obtenir du 225/60 (voir du 400/100 ailleurs dans le quartier) sans G.Fast ? Merci

Informationen zu c.jaquier

Neuste Auszeichnungen

Announced speed of 225/60 Mbps: G.Fast or not?

Announced speed of 225/60 Mbps: G.Fast or not?

⁉️ Issues with IPv6 access to swisscom.ch website

Débit annoncé 225/60Mbit/s : G.Fast ou pas ?

⁉️ Issues with IPv6 access to swisscom.ch website

Announced speed of 225/60 Mbps: G.Fast or not?

Débit annoncé 225/60Mbit/s : G.Fast ou pas ?

⁉️ Issues with IPv6 access to swisscom.ch website

Débit annoncé 225/60Mbit/s : G.Fast ou pas ?

Hier werden erstellte Inhalte angezeigt

Badges für besondere Leistungen

Badges für Aktivitäten