Hello everyone,

I have also updated to 15.00.46 and now I can no longer establish external contact to my 2 Wireguard servers behind the IB3.

It still worked before.

I also made a direct connection to another router on one Wireguard server and this connection can no longer be established.

The ports are not the standard Wireguard ports (51820). I thought this might be the problem because Wireguard is already available.

But with only 3 profiles in the IB3 you can’t get anywhere

Does anyone have any ideas?

Addendum: for example, if I release one server on a Fritzbox as an “Exposed Host”, it runs perfectly again

Show original language (German)
 changed by Tom459
  • Werner has responded to this post.

    Tom459

    Have you already checked the port forwarding and DynDNS?

    To be able to run WireGuard on a Raspi within the internal network of a downstream router, the WireGuard server needs a private port, let’s say UDP 61111 as an example:

    • on IB3 forwarding of port 61111 from IB3 to the IP of the downstream router within the IB3 network
    • On own router Forwarding of port 61111 from own router to the IP of the Raspi within the own network
    • The DynDNS used is best tracked directly on the Swisscom Internetbox, or otherwise using an external service that does not derive the public IPv4 of the Internet access directly from the WAN interface of your own internal router.

    With this setup, my own WireGuard servers (I have 2 of them) continue to work without any problems, even in parallel with the new WireGuard server of the Internet boxes.

    Show original language (German)

    Hobby-Nerd ohne wirtschaftliche Abhängigkeiten zur Swisscom

        Hello Werner,

        I think I was able to solve it. At least it is currently running. :-)
        The ports were/are forwarded correctly, it was apparently the DynDNS.

        There it shows me the address of Swisscom e.g. xyz.internet-box.ch and then I had set up one with my personal domain via Infomaniak. When I deactivated this (“Other DynDNS providers”). It worked via the Swisscom address. When I set up the new one from Infomaniak, it also worked and now it works again.

        At the moment it works with both.

        Apparently the service simply needed a “restart” for the other provider to work properly again.

        Before I reactivated the Infomaniak service on the IB 3, I set it up on my Synology for testing purposes and it worked.

        What should I prefer, the DynDNS on the IB or behind it on another device?

        changed by Tom459

        Werner

        Hello Werner,

        I think I was able to solve it. At least it is currently running. :-)
        The ports were/are forwarded correctly, it was apparently the DynDNS.

        There it shows me the address of Swisscom e.g. xyz.internet-box.ch and then I had set up one with my personal domain via Infomaniak. When I deactivated this (“Other DynDNS providers”). It worked via the Swisscom address. When I set up the new one from Infomaniak, it also worked and now it works again.

        At the moment it works with both.

        Apparently the service simply needed a “restart” for the other provider to work properly again.

        Before I reactivated the Infomaniak service on the IB 3, I set it up on my Synology for testing purposes and it worked.

        Which should I prefer, the DynDNS on the IB or behind it on another device?

        Show original language (German)
        • Werner has responded to this post.

            Tom459

            If possible, update DynDNS directly on the access router (in your case on the Internet box) is the simpler and better solution, because the provider router is the first device to realise if the public IPv4 address actually changes.

            Show original language (German)

            Hobby-Nerd ohne wirtschaftliche Abhängigkeiten zur Swisscom

              10 days later

              I have the impression from the beta firmware that it doesn’t integrate very well with myswisscom.

              It’s telling me that wireless devices are connected by cable when they’re via the WlanBox2 and sometimes there are problems activating the “guest” host WiFi.

              Only Bluetvbox and Wlanbox2 are actually wired.

              Does this do it for you too?

              Show original language (French)
               changed by Jcornu
              6 days later

              Hello community

              I haven’t been able to do the speed test for 2 days. Is this due to this firmware?

              Always the devices connected by the wlan box appear as a wired connection in myswisscom… I have restarted the internet box 3, 1 time since, no better since.

              Show original language (French)
              • user109 has responded to this post.

                Jcornu Please reset the router. Please make a note of all settings beforehand and re-enter all data manually after resetting the Internet box to ensure that no configuration errors creep in from the old backup.

                https://internetbox.swisscom.ch/#applications/speedtest Have you tried this speed test?

                Show original language (German)
                 changed by user109

                    Jcornu couldn’t restore the last 2 backups from myswisscom, I should have made a cfg file. Good reset to factory settings and put the customisations back. See what happens, I still have the same firmware worm indicated 15.00.46.

                    Show original language (French)
                    • user109 has responded to this post.

                        user109 Today the myswisscom app no longer detects my wired Wlanbox2, or at least I think the IB3 doesn’t detect it because it doesn’t appear on the IB3 portal, even though my devices connected to Wlanbox have a connection with the usual speed…

                        I’m going to try restarting both of them during the e-learning break and see if it comes back afterwards.

                        Show original language (French)
                         changed by Jcornu

                          user109 the speedTest works again since the reset to factory settings and the redone configuration of the IB3. Maybe you need to re-register the Wlanbox2 on the IB3, I thought it was automatic if connected by cable…

                          Show original language (French)

                              5018 When is this upgrade coming? As there is no way to go back anymore?

                              This post is in English
                                6 days later

                                user109

                                It seems better these last few days since the complete reset to factory settings and put my options back. The devices just show up as “connection types” on myswisscom and no error message to enable/disable guest WiFi. No more speed test problems either, looks normal. I’ll save the config and hope it lasts. Thanks for your input.

                                Show original language (French)