Hello Paubario19
The mainboard is advertised with Turbo LAN: [https://www.asus.com/ch-de/motherboards-components/motherboards/tuf-gaming/tuf-gaming-z590-plus-wifi/](https://www .asus.com/ch-de/motherboards-components/motherboards/tuf-gaming/tuf-gaming-z590-plus-wifi/) (click Learn More below)
Is there more visible in the settings? Maybe changing the settings will help.
If your Internet Anschluss is faster than 100 Mbit/s, you can easily find out whether your installation is at least gigabit throughout. Please run a speed test with the new PC as it was originally connected with the error:
If you reach a maximum of 100 Mbit/s, you know that the network is not consistently Gigabit Ethernet and then you also know where to start with the renovation.
@hed How can I identify a split installation?
@HP I could try it, I haven’t done anything that has helped yet.
If you take a photo of the multimedia distributor and an open junction box where you can see the connected installation cable and post it here, this should at least be visible to the installation experts here in the forum.
But first I ask you to carry out the speed test according to post #16, that should be easier.
@hed No, I don’t have a universal Gibabit internet, but rather one that is very far away from it. We live away from the village and Swisscom only brings copper over an overhead line and the performance is a maximum of 22Mbit/s.
A renovation to improve the cables in the house is planned but Swisscom isn’t doing anything because they don’t have to on their part.
What may tell you more than me are the diagnoses from the Intel PROSet Adapter Configuration Utility.
Cable test results [12/06/2022 5:50:49 p.m.]:
Cable Quality Status: Failed
Either the cable quality is poor or there is no cable connected. Possible causes: Bad cable, bad Anschluss, or speed/duplex mismatch. Make sure the speed/duplex setting on the switch/hub is configured for auto-negotiation.
Cable Integrity Status: Failed
The test found a bad connection. Distance to the problem: 225 meters.
So 225 meters, there is a problem with Swisscom.
Hardware test results [12/06/2022 5:46:18 p.m.]:
Register status: No errors detected
EEPROM status: No errors detected
FIFO status: No errors detected
Interrupt status: No errors detected
Loopback test(s): No errors detected
NVM health status: Failed
And that is the test for the hardware.
hed This is the measurement. Unfortunately very modest.
@hed Full Ack!
@Paubario19
To test, start with the Turbo options disabled if possible. If no more errors occur, you can activate options again.
By consistent Gigabit Ethernet I only mean the route from the PC to the router (Internet box) and not to the Internet.
“Ergo 225 meters, there is a problem at Swisscom.”
No, the test only takes into account the LAN, i.e. the in-house network up to the router or the next active Ethernet device (in your case the switch), Swisscom is only responsible for the WAN, i.e. the external feed.
@hed So you need 1 picture of the multimedia box and 1 picture of the house connection box where the Swisscom comes in and then goes into our house with the “fuses”?
@hed As far as I know, the cable from the router to the switch is just a Cat. 5e installation but everything afterwards is installed with at least Cat. 6a.
(and this so-called cable is planned for a revision)
What does it show when you enter 192.168.1.1 in the Internet browser and then click the mouse on the top left green dot, see example image below.
Have you already asked whether it is possible to use the 5G booster to get more speed?
Installationen, Netzwerk, Internet, Computertechnik, OS Windows, Apple und Linux.
@Paubario19 wrote:
… the color is green on the switch.
Hmm, can you limit this somewhere in games or in general?
And the one next to it is yellow? Is there a cable coming from these two sockets at the back that is combined? -> then you have a split installation and that will cause problems.
This is the first time I’ve read that the image resolution has an influence on the bandwidth required when playing online games. The connection is required for position information, but the image is calculated by the graphics card.
@Paubario19 wrote:
@hed So you need 1 picture of the multimedia box and 1 picture of the house connection box where Swisscom comes in and then goes into our house with the “fuses”?
No, from the multimedia box and a LAN socket in the house where you plugged in the PC or the switch in front of the PC.
P.S.:
Can you please also provide the desired screenshots according to posts 25 and 30.
@Paubario19 wrote:
@hed As far as I know, the cable from the router to the switch is just a Cat. 5e installation but everything afterwards is installed with at least Cat. 6a.
(and this so-called cable is planned for a revision)
Cat. 5e is very suitable for Gigabit Ethernet and does not need to be replaced. And Cat. 6a or even Cat 7 alone says nothing about how the installation is done. If it is designed as a split multimedia, i.e. an 8-wire cable is split between 2 LAN sockets, this can be very problematic.
