@Studermarc009 wrote:
I tried that from the beginning, but it didn’t work, so I’ve been testing without the home network since then.
The problem is that the IB2 simply doesn’t want to connect to the converter.
But you already waited over 5 minutes after reconnecting?
Try switching off the Internet box and then installing the whole thing and then switching it on again after installing and waiting 5-8 minutes!
Installationen, Netzwerk, Internet, Computertechnik, OS Windows, Apple und Linux.
Yes, then I’m running out of ideas, it could still be that one of the modules is actually defective. Maybe someone else will tell you where these modules are in operation, you can hardly do anything wrong if you follow the instructions.
N.B. and the short LAN cable from the Internet box to the adapter is also OK?
Installationen, Netzwerk, Internet, Computertechnik, OS Windows, Apple und Linux.
I’m not sure whether it necessarily has to be a 1Gbit LAN cable, i.e. with 8 wires and not just 4 wires, is that the case? When I tested it with the notebook, it didn’t show whether it had 4 or 8 wires, only if the network card was for 1 Gbit/s is suitable then the speed test should show this on the Internet box.
Installationen, Netzwerk, Internet, Computertechnik, OS Windows, Apple und Linux.
@cypherpunks wrote:
I’m not sure about Walter’s picture of the fiber optic connection!
LAN1/2 and LAN7/8 connections on the patch panel do not match the connections on the multimedia sockets? Is this sketch from Swisscom correct….
The sketch is wrong. Of course it has to be 1 to 1.
@Studermarc009 will be able to test it in a few days. SFP Ethernet has been ordered.
Addendum 12/3/17 works. See article: [https://community.swisscom.ch/t5/Internet/Glas Fiber Connection-in-a-Wall Cabinet/td-p/452540/page/9](https://community.swisscom.ch/t5/Internet /Fiber optic connection in a closet/td-p/452540/page/9)
w_37 wrote:
Especially since I can’t find the Skyline anywhere, just like the Cisco… Where did you find it?
http://www.steg-electronics.ch/de/article/product-14184709.aspx
ps: I had a second media converter for sale cheaply (accidentally ordered two)
You bought too expensively. I only paid 18 euros on Ebay for the Ethernet SFP.
[http://www.ebay.de/itm/Skylane-SGT00P10DR00-RJ45-transceiver-copper-10-100-1000Base-mini-gibic-SFP-/331069485555] (http://www.ebay.de/itm/Skylane-SGT00P10DR00-RJ45-transceiver-copper-10-100-1000Base-mini-gibic-SFP-/331069485555)
Solution 2 is the absolute most sensible one.
Ideally, it is best to separate routing and WiFi. Since the AIO Combos (All in One Routers) are very powerful, it makes sense to distribute the tasks.
If the apartment is larger than 120m2 or is spread over 2 floors, there is no way around it.
Therefore install an IB 1 in the closet. Be sure to check whether the distribution connections are set to 100Mb or 1000Mb. Otherwise everything is a waste anyway. In the worst case, the customer loses half of his ports in the closet (I recently converted this for a customer: 500Mb subscription but only 100Mb network at home in a 4-year-old apartment on the “Gold Coast”! Swisscom technicians and Dataquest supporters don’t have it on site noticed!!!).
If IB1 cannot be installed then the media converter is the only sensible solution. Extending glass is not exactly cheap and can only be done under difficult circumstances in a rented apartment.
Basically, it’s not a “stupid” idea to banish the router into the closet, but it should be implemented ergonomically and sensibly from the ground up.
As an electrical fitter, I’ve seen a lot of good things, but a lot of things are messed up in the interests of the company carrying out the work, which ultimately harms the customer.
@Informatik Klinik wrote:
.. In the worst case, the customer loses half of his ports in the cabinet (I recently converted this for a customer….
How did you remodel that?
Thomas
He had run a cable to each socket. However, two R&M Freenet LAN ports per cable were connected in the closet and socket.
I have now reconnected the cable to just one LAN socket so it has GigaLan. Unfortunately “the electrical company” didn’t even use shielded cables, but they are fireproof:smileylol:
